Home > Xp And > Xp And Win98 + Router!

Xp And Win98 + Router!

Click OK. User/Group Name would be any name you want to give to that computer, Enable should be checked, IP Address/IP Range would be the clients address and WWW and Mail should be To install the mdmcisco.inf file, add a modem as follows: Choose Start > Settings > Control Panel > Phone and Modem Options. Is that correct?

posted 20 Sep 2007 - show 1 replies - Reply - Permanent Link Admin Administrator this guide only covers windows networking. Router Setup URL Username Password Linksys http://192.168.1.1/ admin D-Link http://192.168.0.1/ admin Netgear http://192.168.0.3/ or http://192.168.1.1/ admin password SMC http://192.168.2.1/ 2wire http://192.168.0.1/ or http://gateway.2wire.net/ admin If your You may be interested in our other Windows XP guides. Verify that the maximum speed of the COM port is set to match the speed configured under the async port on the Access Server side.

The information here is accurate to the best of my knowledge. I would also like to know what i would need besides a ethernet card (RJ45) and cable (special cable?). Check Use IP Header Compression and Use Default Gateway on Remote Network to verify that they are properly selected. Now I have started browsing the net for wired routers and it looks like they have gone the way of the dinosaurs, wireless seems the preferred system now but sounds like

I don't know anything about routers and the more I read about them the more I get confused. Click OK. But whenenver we want to play a lan game, we are unable to join and sometimes unable to even see the game. The Proxy Way by using CCProxy The disadvantages of using a proxy server is that you cannot use any application that requires a direct connection to the other party.

network xp comp to win98 without router. Articles & News Forum Graphics & Displays CPU Components Motherboards Games Storage Overclocking Tutorials All categories Chart For IT Pros Get IT Center Brands Tutorials Other sites Tom's Guide Tom's IT Configure it such that all your home network computers are in the Trusted Zone. 2) I can't find/connect to my PC Network Server! Then, reboot. (You could also click on ACTION and select SCAN FOR HARDWARE CHANGES but I prefer to reboot anyway.) Windows will redetect the NIC and reinstall the drivers and set

HKR, Responses, "", 1, 02, 00, 00, 00, 00, 00, 00,00,00,00 ; Accept any recvd data as CONNECTED. !--- Note: The lines of code above are each displayed over two lines HKR,, Properties, 1, 00,00,00,00, 00,00,00,00, 00,00,00,00, 00,00,00,00, 00,00,00,00, 30,00,00,00, 00,c2,01,00, 00,c2,01,00 !--- Note: The line of code above is displayed over two lines due to space limitations. But you can search eBay for a used Linksys Wired Router for the same price---but you'd still need the cable...10, 20 bucks? Configure Windows 98 Dial-up Networking by following these steps: From the Start menu, choose Programs > Accessories > Communication > Dial-up Networking.

Because each router has its own setup interface, here are some URLs to configure common routers. Enter the IP address of the PC that is running the server. 4) Sharing one Internet connection with the other computers (WITHOUT router) There are two options for sharing an Internet However, using the Network Setup Wizard may not be preferred as it does not give much control. This is the best way to go, Of all info on networking on the net.

Hold the CTRL key and highlight the other NIC. I was told by someone that it is possible without a router. Prerequisites Requirements There are no specific requirements for this document. including caps...

Now it should say under the status: Connected! Questions about adding propane for just a stove top [HomeImprovement] by vircotto273. When I try to access the 98 computer on my XP computer I am told that the computer is not accessible and that the network path cannot be found. The Cisco modem adapter part number is 74-0458-01 (revision A1).

win xp ... Note:The speed you select must match the maximum speed of the router async port. Results 1 to 3 of 3 LinkBack LinkBack URL About LinkBacks Bookmark & Share Add Thread to del.icio.usTweet this thread Thread Tools Show Printable Version Email this Page… Subscribe to this

Note:Ensure that the speed set under Generic Null Modem Properties is the same speed of the Access Server async port.

You should find the Generic Null Modem installed on the COM port you selected during installation. That cabling should connect the PC and the Cisco Access Server (the Data Terminal Equipment [DTEs]) without the need for a null-modem cable. Type the name exactly... Obtain or create the mdmcisco.inf file (refer to Step 1 of the Windows 98 Dial-up Networking by a Null-Modem Cable section of this document).

Enter the username and password that is valid on the Access Server. In the window that is displayed, verify that the Server Assigned IP Address and Server Assigned Name Server Address radio buttons are selected. It just chugs away, day in, day out, waiting to be told to print to one of the connected printers or to store another card's worth of happy snaps of the I remember seeing that in Zone Alarm before.

Under Advanced Settings, the default Flowcontrol Hardware should remain selected.