Home > Xerox Phaser > Xerox Phaser 8500 Print Quality - Fuzzy Print

Xerox Phaser 8500 Print Quality - Fuzzy Print

It's also supposed to provide better graphics. Wait while the printer completes the calibration, and then touch OK. Do not replace cartridges to fix vertical streaks. To print the manual completely, please, download it. http://comvurgent.com/xerox-phaser/xerox-phaser-8500-error-code.html

Or occasionally, a page or two in the middle of a print job may be fuzzy. The Print Quality Diagnostics Page prints. Question about Xerox Phaser Office Equipment & Supplies 1 Answer Fuzzy page continious. ...print the first and sometimes the second one with the fuzzy style. Initial Actions ■ Check the media used is supported by this printer. ■ Check that the paper path is clean and clear of debris.

Comes with instructions to replace or found on Xerox's site under support for the machine. On the test print the blue lines are not straight or of even colour quality. This umbrella program has a searchable interface that contains all kinds of information about the printer (from the user guide to troubleshooting to ordering supplies) and also houses the printer-status monitor. If Test Pattern 2 still displays white lines across the color blocks, continue to the next solution.

This content is provided “AS IS” and is subject to change or removal at any time. We don't recommend this printer if you plan to make lots of full-page color prints. How are you submitting the print jobs? If there are still defects on the report after another cleaning, skip to the solution in this document to replace one or both printheads .

Message 4 of 12 (11,605 Views) Reply 0 Kudos MarkGHC New Member Posts: 6 Registered: ‎05-10-2011 Re: Phaser 8550 DP inconsistant blurry prints Options Mark as New Bookmark Subscribe Subscribe to We have used the mainenance mode lots of times but it hasn't worked. Go to Contact HP Support to review available service options. If you completed all the preceding steps and your product still has an issue, you might need further assistance from HP.

Load plain white paper into the tray. If the ink tubes are bundled incorrectly and are kinked, read the following list, and then skip to Service the printer in this document. Restore password × Upload manual upload from disk upload from url Thank you for your help! × AdBlocker Detected! Cleaning the temperature sensor as you suggested has not solved the problem.

Also the encoder is stuck on the side of the drum with adhesive. by Hallival on Nov 23, 2011 at 9:52am Add comment Please sign in to comment 1 Not sure if I messed up or not but I was thinking I had to To help others who may have the same or similar issue that you were experiencing, could you please click on the "Accept as Solution" button in the bottom right corner of Click Advanced.

Figure 16: Remove the printhead Step 3: Install the new printhead Shake the printhead up and down at least six times while the printhead is still in its packaging. weblink Printing a 2-Sided on page 95. Privacy Policy Terms of Use Sign In Upload Page of 376 Go Download Table of ContentsContents TroubleshootingTroublesh.. I stress MAY be the issue.

Figure 5: Vertical streaks in printout Do not replace cartridges for vertical streaks in a printout. Tom tchandler, Oct 23, 2008 #3 arknorth Joined: Oct 17, 2007 Messages: 1,099 There's not too many brick-types out there, and the only other heavy-duty color I've worked with on Message 9 of 12 (11,554 Views) Reply 0 Kudos JohnM-Xerox Xerox Employee Posts: 416 Registered: ‎10-29-2010 Re: Phaser 8550 DP inconsistant blurry prints Options Mark as New Bookmark Subscribe Subscribe to navigate here The encoder disk being right beside the drum, overtime oil is bound to get on the encoder disk.Drum Encoder Disk   Cleaning Procedure For Fuzzy or Blurred Print on the Xerox

Show Ignored Content As Seen On Welcome to Tech Support Guy! One page will look to have some dots shifted slightly and another page will look almost streaky because the dots are off by about half an inch. Figure 8: Ink tubes, correctly bundled and not kinked If the ink tubes are bundled correctly and are not kinked, continue to the next step.

Drives people in the office crazy...

This determines if the problem is related to the paper. ET. To avoid issues that require cleaning the printhead, always turn the printer off with the Power button on the printer itself. Generated Sat, 18 Mar 2017 12:51:40 GMT by s_hv1050 (squid/3.5.23)

Laser Printer Repair and Fax, Copier Service ArticlesThis Website is Dedicated to Providing Free Service and Repair Articles Designed to Help Service Technicians or End Users Fix Their Printer, Copier, or Many thanks! HP cannot guarantee the quality or reliability of non-HP or refilled cartridges. his comment is here The encoder is on the right side of the drum under the fan.

The Print Quality Diagnostics Page helps you determine if the printer needs to be aligned, or if the printheads need to be cleaned, or if the linefeed needs to be calibrated. Check the Roll Block alignment. If there are no defects on the report, stop troubleshooting. Touch Setup (), and then touch Tools.

I don't want to scrap the machine, which will be the preferred option if I need to pay that sort of fee even to find out what the problem is.Many thanks,RR Advertisement Recent Posts Portuguese characters not... You'll still complete secure or personal print jobs through the physical interface to prevent others from accidentally picking up your work from the output tray.

A door on the top reveals