Home > Xerox Phaser > Xerox Phaser 8500 False Reading On Missing Maintanence Kit

Xerox Phaser 8500 False Reading On Missing Maintanence Kit

Phaser 8400-Series Printer Configurations Features 8400B... If POST diagnostics pass, the Control Panel displays the Xerox logo and turns on the green LED. Tray 4 pick flag sensor timed out while printer imaging. or damaged. http://comvurgent.com/xerox-phaser/xerox-phaser-8500-error-code.html

To avoid personal injury, do not perform any servicing other than that contained in the operating instructions, unless you are qualified to do so. Sensors maintain correct operating temperatures for the printhead and drum. The exit door open flag unexpectedly tripped while the printer was performing a normal shutdown. Did this correct the problem? 3-24 Phaser 8400/8500/8550 Color Printer...

Page 80 Did this fix the problem? Replace the I/O board, then retest. 3-62 Phaser 8400/8500/8550 Color Printer... Page 45 A closed-loop servomotor drives the drum assembly. Troubleshooting Procedure for Ink Loader Step Questions and Actions Are the ink sticks all Xerox ink?

Wiper Shaft Cycles the motor/shaft repeatedly until interrupted by a Control Panel button press. A signed copy of the Declaration of Conformity for this product can be obtained from Xerox. R values have alternate definitions or are unused depending on the pick tray and if simplex or duplex path was selected. A larger value could indicate particles in the gears or non uniform contamination of a roller (causing a lump). 4-20 Phaser 8400/8500/8550 Color Printer...

Page 57 Release Blade Strip Solenoid Exit Sensor Transfix Roller Preheat Sensor Strip Sensor Paper Preheater s8500-027 Theory of Operation 2-29... Ask The Expert Event Device Connectivity Remote Services - Ask the Expert Event FreeFlow Production Workflow Forum FreeFlow Core FreeFlow Digital Publisher FreeFlow VI Suite Community Suggestions Community Suggestion Box Home Page 176 Swing Arm .03 to .06 Reports the time that the lower Transition Time (sec) portion of the paper path drive is disconnected while the swing arm transitions to the Ensure ground integrity for the printer (see "Ensuring Ground Integrity" on page 4-77).

Troubleshooting Procedure for I/O Board Step Questions or Actions Are all wiring connections to and from the Go to Step 3. The Media Path Drive: Controls each roller in the paper transport system. The system returned: (22) Invalid argument The remote host or network may be down. Please try the request again.

Replace the pivot arm. The power control board regulates +/- 15 V to +/- 12 and other voltages. Check the wiring to the tray 2 lift motor. Page 110 8500/8550 PEST description 37,016.43: PEST 50 V power supply test.

Replace the EEPROM chip. 3-12 Phaser 8400/8500/8550 Color Printer... his comment is here Inspect the Tray 1 wiring to the I/O board. 5. The second table shows the configuration for the 8500 series. Page 195 Temperature Status (Continued) This test scans the thermocouples and reports data on the current temperature with the goal of providing a picture of the current temperature state of the

For 50 V power supply test. gearbox. On-site Printhead Troubleshooting Checklist (8400)page 388................................................................................................................................................................ this contact form Typical Typical Value Value (8400) (8500/ Definition...

Miscellaneous Electrical Troubleshootingpage 205................................................................................................................................................................ Hard drive (optional) 3. general troubleshootingpage 143................................................................................................................................................................

Phaser 8400/8500/8550 Color Printer...

Go to Step 7. Page 157: Check Shafts Menu, Deskew Shaft Check Shafts Menu Deskew Shaft Runs the media path drive train and engages the deskew clutch on the fly then disengages the clutch. Tray 2 Pick Unused Unused 4-26 Phaser 8400/8500/8550 Color Printer... Page 42: Purge System The wiper blade lowers and wipes excess ink from the jets into the ink waste tray.

Did the test pass? Your cache administrator is webmaster. In addition, because the purge tubing also acts as a vent to atmosphere when not purging, a more serious failure may occur if the ink overfills. navigate here Page 132 4.

Process drive Swing gear Imaging Transfix Transfix Camshaft Process Motor Gear Process Motor Gear Drum Maintenance Camshaft Drum Maintenance s8500-009 Phaser 8400/8500/8550 Color Printer... Bond) 257 mm) 1-12 Phaser 8400/8500/8550 Color Printer... Complete. Troubleshooting Procedure for Tray 1 Step Questions and Actions Check the wiring and connectors from the Go to Step 2.

drum temperature Did the test pass? Page 41: Drum Maintenance System Drum Maintenance System The drum maintenance system creates a thin intermediate liquid transfer surface, a layer of silicone oil, on the surface of the drum prior Page 9: Table Of Contents Contents User Safety Summary ......... Copyright protection claimed includes all forms of matters of copyrightable materials and information now...

R values have alternate definitions or are unused depending on the pick tray and if simplex or duplex path was selected. One camshaft assembly controls the transfix roller loading, and the other controls the drum maintenance system and printhead tilt system. Page 178 Roll With Transfix Roller Down interval (mpts) Time to last .300 to 0.30 to Reports the time from the unload contact (sec) 0.450 0.80 command to the engine until Function Menu A submenu containing a set of functions for commanding more complex actions by portions of the printer mechanism.

Y-Axis motor stalled while the printer performed printhead purge. The Y-Axis uses an active tension system to allow the pulley to float while the spring actively adjusts the tension.